Guide · Homeowners · 4 min read · Updated 17 November 2026
How to Treat and Refinish a Wooden Gate: Oil, Stain or Paint?
Short answer
Choose oil for hardwood gates you want to keep looking natural, stain or a coloured preservative for softwood gates, and exterior paint for a solid colour with long-lasting protection. Whatever you use, clean and sand back to sound timber first and treat all faces and end grain. In the UK, professional cleaning, sanding and refinishing of a gate typically costs £120–£300.
Why gates need regular treatment
Timber gates take a battering from the weather. Sunlight breaks down the surface fibres and turns untreated wood silver-grey. Rain soaks into end grain and joints, the timber swells and shrinks with the seasons, and over time joints loosen, boards split and rot gets a foothold. A good finish slows all of this down and keeps water out of the places it does most damage.
Treatment is far cheaper than repair. A gate refinished every few years will usually outlast one that is left until boards are splitting and rails are soft.
Oil, stain or paint compared
Each finish suits different timbers and looks. Oils soak into the wood and keep its natural appearance, which suits oak, iroko and other hardwoods. They need re-applying more often but are easy to refresh without sanding back. Stains and coloured preservatives suit softwood gates, adding colour and some protection while showing the grain. Exterior paints form a film that gives the most colour choice and longest interval between coats, but they need careful preparation and eventually peel if neglected.
| Finish | Best for | Look | Maintenance |
|---|---|---|---|
| Exterior wood oil | Hardwood gates | Natural, enhances grain | Refresh often, no sanding back |
| Stain or coloured preservative | Softwood gates | Coloured, grain visible | Re-coat every few years |
| Exterior paint system | Any timber, solid colour | Opaque, wide colour range | Longer interval, sand peeling areas |
| Clear preservative | New treated softwood | Natural, may grey over time | Usually combined with a top coat |
Preparing a weathered gate
Preparation decides how long a finish lasts. Start by brushing off loose dirt and cobwebs, then wash the gate to remove algae and grime. A pressure washer can raise the grain and force water into joints, so a stiff brush and a suitable timber cleaner are often kinder to old gates. Let the timber dry thoroughly before going further.
Sand off loose fibres, flaking finish and greyed surface timber until you reach sound wood. Pay attention to the top rail and bottom edge, where weathering is worst. Any rotten sections should be cut out and replaced before finishing, as no coating will save soft timber.
- Brush and wash off dirt, algae and moss
- Let the timber dry completely
- Sand back flaking finish and greyed surface
- Replace rotten boards or rails first
- Remove or mask hinges and latches
- Apply finish to all faces and end grain
Applying the finish properly
Work on a dry day when rain is not forecast for the drying time stated on the product, and avoid applying in strong direct sun or frost. Two thin coats are better than one thick one. Brush along the grain and work the finish into joints and the end grain at the top and bottom of boards, as these soak up most water.
If possible, take the gate off its hinges and lay it flat to treat the edges and bottom, which are almost impossible to reach when it is hanging. Remove or mask hinges and latches rather than painting over them, so they keep working and can be replaced easily later.
How often to re-treat
There is no single answer, because exposure matters as much as the product. A gate facing south or near the coast weathers far faster than one in a sheltered side passage. As a rule, oiled hardwood gates benefit from a fresh coat every year or two. Stained softwood gates usually need re-coating every few years, and well-prepared painted gates can go longer between coats.
Watch for the early signs: water no longer beading on the surface, colour fading on the top rail, or paint starting to crack at joints. Refreshing at that point is a quick job. Waiting until the finish has failed means sanding back to bare wood again.
Professional refinishing costs
In the UK, professional cleaning, sanding and refinishing of a gate typically costs £120–£300, with two coats of stain, oil or paint included. A single side gate sits at the lower end and a pair of double driveway gates at the top. If boards or rails need replacing first, those repairs usually cost £120–£280 on a typical side gate.
Combining refinishing with other repairs, such as new hinges or a rehang, often saves money compared with booking them separately. Through us, you can request quotes from local specialists who can repair and refinish your gate in one visit.
Common refinishing mistakes
The most frequent mistake is coating over a problem. Paint or stain applied to damp timber traps moisture inside, which leads to blistering, peeling and rot underneath a finish that still looks fine from a distance. Coating over green algae or loose grey fibres has the same effect, because the new finish bonds to the dirt rather than the wood.
Another common error is treating only the faces you can see. The bottom edge, the tops of boards and the back of the hinge stile are where water gets in, and they are often missed when a gate is painted in place. Mixing incompatible products causes trouble too, such as putting a water-based stain over a fresh oil, or a film-forming paint over a finish designed to soak in.
Finally, avoid heavy coats in the hope of making the job last longer. Thick layers dry slowly, stay soft and crack sooner. Thin, even coats with the right drying time between them give a much tougher result.
Questions people also ask
Can I paint a gate that was previously oiled?
Usually, but oiled timber resists paint adhesion. The gate needs cleaning with a suitable degreaser or timber cleaner, sanding back and leaving to weather for a while if the oil was recent, before priming. Check the paint maker's guidance for previously oiled surfaces, as some primers are designed for this.
Should I treat a new pressure-treated gate?
Pressure treatment protects the timber against rot, but it does not stop it weathering, splitting or greying. Many treated gates benefit from a coloured preservative, stain or paint once the timber has dried out, which helps keep water out of the surface and joints. Always treat any cut ends.
What is the best time of year to refinish a gate?
Late spring to early autumn, on a dry spell when the timber has had time to dry out. Avoid frost, rain forecast during the drying time, and very hot direct sun, which can make finishes dry too quickly. Check the product's recommended temperature range on the tin.
Written and checked by the Wooden Gate Repair team. Read our editorial policy.
More guides
Wooden Gate Repair Cost UK: 2026 Prices for Common Jobs
In the UK in 2026, rehanging and bracing a sagging side gate typically costs £90–£180. Replacing a timber gate post costs £180–£350 per post, new…
How to Fix a Sagging Wooden Gate (and Stop It Dropping Again)
To fix a sagging wooden gate, first find the cause: loose hinge screws, a weak or missing diagonal brace, loose joints or a leaning post. Tighten or…
Replacing a Rotten Gate Post: Methods, Materials and Costs
A rotten gate post is replaced by removing the gate, digging out the old post and its concrete, setting a new treated softwood, hardwood or…
Repair or Replace a Wooden Gate? How to Decide
Repair a wooden gate if the frame is mostly sound and the problem is sagging, loose fittings, a few rotten boards or a rotten post. Replace it if rot…
Get a free wooden gate repair quote
Tell us what you need and we'll come back with a clear price.
Request a quote