Wooden Gate Repair
Gate Post Replacement
Removing rotten or leaning timber posts and setting new treated softwood, hardwood or steel-reinforced posts in concrete or post supports.

What's involved
Gate posts carry far more load than fence posts, because the weight of the gate acts like a lever pulling the top of the post forward. Rot almost always starts just below ground, where wood stays wet. The old post is dug out along with its concrete collar, which can take time if it was set in a large lump. A new post, usually 100mm or 125mm square pressure-treated timber rated for ground contact, or hardwood for heavier gates, is set at least 600mm deep in concrete shaped to shed water away from the timber. For wide or heavy gates, the specialist may fit a steel post or a concrete spur. Posts are braced while the concrete sets and the gate is rehung once it is firm, usually the next day. Expect half a day to a day per post.
How we handle it
Send photos and details
Use the quote form to tell us what is wrong, the gate's size and timber type, and whether it is a side gate or driveway gate. Photos of the hinges, posts and bottom rail let a specialist judge the repair quickly.
Assessment
A local carpenter checks the posts for rot and lean, the frame for loose joints and the fittings for wear. They will say plainly whether the gate is worth repairing or should be replaced.
Clear quote
You receive one price covering labour, timber, fittings and concrete, plus taking away old timber. Most small repairs are priced on the spot from your photos or at a short visit.
Repair work
Posts are reset first, then the frame is squared, rotten parts replaced and new fittings added. Where posts are set in concrete, the gate is usually rehung the next day once it has firmed up.
Adjust and finish
The gate is adjusted so it swings clear of the ground and latches cleanly, then new timber is treated. The specialist tidies up, removes waste and explains how to keep the gate in good order.
Price guide
Wooden gate repair is usually priced per job, based on what needs doing and the materials involved. Small fixes such as rehanging a sagging gate or swapping a latch cost much less than replacing a post set in concrete. The guide prices below are typical for UK homes in 2026 and include labour and standard materials.
- Replace hinges and latch: £80–£160. Supply and fit of galvanised or black hinges and a new latch or lockable bolt.
- Replace rotten bottom rail or boards: £120–£280. Cutting out damaged timber, fitting matching sections and treating new wood on a typical side gate.
- Clean, sand and refinish a gate: £120–£300. Two coats of stain, oil or paint; double driveway gates sit at the top of the range.
Questions about gate post replacement
How often should I treat a wooden gate?
Softwood gates with stain or paint usually need recoating every three to five years. Hardwood gates finished with oil benefit from a fresh coat every one to two years. Treat any new timber and cut ends straight away, as bare end grain soaks up water.
Do I need planning permission to replace a wooden gate?
Not usually, if the new gate is a similar size to the old one. In England, gates over 1 metre next to a road used by vehicles, or over 2 metres elsewhere, generally need permission. Listed buildings and some conservation areas have extra controls.
Can you make my side gate lockable?
Yes. Options include padlockable bolts, lockable ring latches and key-operated gate locks that work from both sides. A secure side gate is one of the simplest ways to protect the back of a house, and some insurers ask whether side access is lockable.
Other services
Sagging Gate Rehanging
Lifting and squaring dropped gates, fixing loose joints, adding diagonal bracing and refitting hinges so the gate swings clear and latches first time.
Rail and Board Repairs
Replacing split boards, rotten bottom rails and broken stiles, matching timber where possible so the repair blends in with the original gate.
Hinge, Latch and Lock Replacement
Fitting new hinges, latches, bolts, drop bolts and gate locks, choosing heavy-duty, galvanised or stainless fittings to suit the gate and exposure.
Gate Restoration and Refinishing
Cleaning, sanding and re-treating weathered timber gates with preservative, oil, stain or paint to bring the colour back and protect the wood.
Made-to-Measure Replacement Gates
When a gate is beyond saving, a new timber gate built or supplied to fit the opening exactly, hung on new posts and fittings.
Gate Post Replacement near you
Get a free wooden gate repair quote
Tell us what you need and we'll come back with a clear price.
Request a quote