Guide · Homeowners · 4 min read · Updated 17 November 2026
Repair or Replace a Wooden Gate? How to Decide
Short answer
Repair a wooden gate if the frame is mostly sound and the problem is sagging, loose fittings, a few rotten boards or a rotten post. Replace it if rot has spread through the stiles and rails, the gate has twisted badly, or repairs would cost close to a new gate. In the UK, common repairs cost £80–£300 each, while a new made-to-measure softwood side gate fitted starts from £350.
Start with an honest inspection
Before deciding, check the gate methodically. Push a screwdriver into the bottom of each stile, the bottom rail and the lower end of the boards. Look at the joints between the rails and the stiles for gaps and movement. Open and close the gate and watch whether it twists or flexes. Finally, check the posts at ground level, because a failing post can make a sound gate look broken.
Many gates that look ready for the bin turn out to have a sound frame with a few bad boards, tired fittings and a post that needs replacing. Others look fine from a distance but have rot running inside the joints.
- Probe stiles, rails and board ends for soft timber
- Check joints for gaps and movement
- Watch for twisting or flexing when opened
- Test posts at ground level
- Look at hinges and latches for rust and wear
When repair is the right choice
Repair makes sense when the core of the gate is solid. Sagging caused by loose hinges or a missing brace is a quick fix. A couple of split boards or a rotten bottom rail can be cut out and replaced with matching timber. Rusty hinges and latches can be swapped for galvanised or stainless fittings. Even a rotten post is a repair rather than a reason to replace the gate.
Repair is especially worthwhile for hardwood gates, bespoke designs and gates that match a fence or the house, because a like-for-like replacement would be expensive. Weathered timber that is structurally sound can be cleaned, sanded and refinished to look much better.
When replacement makes more sense
Replacement is usually the better choice when rot has spread into the stiles and multiple rails, when the gate has twisted so badly it can no longer be squared, or when the original gate was poorly made from thin timber. If you need a new post, new fittings, several boards and a rehang all at once, the combined cost can approach a new gate.
A new made-to-measure gate also gives the chance to fix design flaws, such as a missing brace, too little ground clearance or a flat top rail that holds water.
Comparing the costs
Adding up likely repair costs and comparing them with a replacement helps make the decision clearer. The figures below are typical UK guide prices for 2026, including labour and standard materials. Hardwood and wide driveway gates cost more for both repairs and replacements.
| Option | Guide price | Good choice when |
|---|---|---|
| Rehang and brace | £90–£180 | Frame sound, gate has dropped |
| Replace hinges and latch | £80–£160 | Fittings rusted or worn |
| Replace rotten bottom rail or boards | £120–£280 | Rot limited to a few parts |
| Clean, sand and refinish | £120–£300 | Timber sound but weathered |
| Replace timber post | £180–£350 per post | Post rotten or leaning |
| New softwood side gate fitted | from £350 | Rot widespread or gate twisted |
Thinking about the long term
A repaired gate will only last as long as its weakest part. If you repair one rail on a gate where the others are close to failing, you may be paying for another repair next year. A good repairer will be honest about this and tell you if the remaining timber is near the end of its life.
On the other hand, a solid gate with fresh fittings, a proper brace and a new post can give many more years of service for much less than replacement. The key is fixing the cause, not just the symptom, whether that is water pooling at the base of a post or a top rail that soaks up rain.
Getting impartial advice
Because the decision depends on what is inside the timber, a site visit is the best way to decide. Ask whoever inspects the gate to price both options, so you can see the difference rather than being steered one way. Clear photos of the gate, hinges, posts and any damaged areas help a repairer give an early idea before visiting.
Through us, you can request quotes from vetted, insured local specialists who carry out both repairs and replacements, so they have no reason to push one over the other.
If you choose a replacement gate
If replacement wins, use the opportunity to get a gate that will last. Ask for a framed or properly braced design with the brace running the right way, a top rail that sheds water, and enough clearance at the bottom so the gate does not sit in wet grass or leaves. Specify galvanised or stainless hinges and a latch that suits how you use the gate, whether that is a simple thumb latch, a lockable bolt or a key-operated lock for a side passage.
Choose the timber to match your budget and the look of the property. Treated softwood is the economical choice and takes paint or stain well. Oak and iroko cost more but are heavier, stronger and suit period homes and driveway gates. A made-to-measure gate fits the opening exactly, which avoids the large gaps and packing pieces that come with off-the-shelf sizes.
Check the posts at the same time. Hanging a new gate on a tired post is a false economy, because the post will fail first and take the new gate down with it.
Questions people also ask
How long does a wooden gate last?
A well-made treated softwood gate that is maintained can last many years, and hardwood gates longer still. Lifespan depends on timber quality, design details such as bracing and ground clearance, exposure to weather and how often it is treated. Neglected gates in wet, shaded spots fail much faster.
Can a gate be partly rebuilt using the old timber?
Yes. A repairer can keep sound stiles and rails and replace only the failed parts, matching board profiles where possible. This is common with hardwood and bespoke gates. New timber will look different from weathered timber at first, so refinishing the whole gate afterwards helps it blend in.
Will a new gate fit my existing posts?
A made-to-measure gate is built to fit the opening, so it can hang on existing posts if they are sound, upright and strong enough. If the posts are rotten, leaning or too slim for the new gate's weight, replacing them at the same time gives a much better result.
Written and checked by the Wooden Gate Repair team. Read our editorial policy.
More guides
Wooden Gate Repair Cost UK: 2026 Prices for Common Jobs
In the UK in 2026, rehanging and bracing a sagging side gate typically costs £90–£180. Replacing a timber gate post costs £180–£350 per post, new…
How to Fix a Sagging Wooden Gate (and Stop It Dropping Again)
To fix a sagging wooden gate, first find the cause: loose hinge screws, a weak or missing diagonal brace, loose joints or a leaning post. Tighten or…
Replacing a Rotten Gate Post: Methods, Materials and Costs
A rotten gate post is replaced by removing the gate, digging out the old post and its concrete, setting a new treated softwood, hardwood or…
How to Treat and Refinish a Wooden Gate: Oil, Stain or Paint?
Choose oil for hardwood gates you want to keep looking natural, stain or a coloured preservative for softwood gates, and exterior paint for a solid…
Get a free wooden gate repair quote
Tell us what you need and we'll come back with a clear price.
Request a quote