Guide · Homeowners · 3 min read · Updated 17 November 2026
How to Fix a Sagging Wooden Gate (and Stop It Dropping Again)
Short answer
To fix a sagging wooden gate, first find the cause: loose hinge screws, a weak or missing diagonal brace, loose joints or a leaning post. Tighten or move hinge fixings into sound timber, square the gate, then fit or refit a diagonal brace running from the bottom hinge corner up to the top latch corner. If the post has rotted or leans, it must be replaced before the gate will hang true.
Why wooden gates sag
A gate is a cantilever. All its weight hangs from one side, so gravity is constantly trying to pull the latch end down. A well-built gate resists that with a rigid frame and a diagonal brace that carries the load back to the bottom hinge. When any part of that system weakens, the latch end drops, the gate scrapes the ground and the latch no longer lines up.
The usual culprits are hinge screws that have worked loose in softening timber, joints that have opened up as the wood dried and swelled through the seasons, a brace fitted the wrong way round or missing altogether, and a hinge post that has started to rot or lean. Often it is a combination of two or three of these.
- Loose or stripped hinge screws
- Missing or wrongly angled diagonal brace
- Opened joints between rails and stiles
- Hinge post rotting or leaning at ground level
- Hinges too light for the gate's weight
Diagnose before you fix
Start by lifting the latch end of the gate gently. If the hinges move or the screws pull in and out, the problem is the fixings. If the hinges stay put but the gate frame flexes and goes out of square, the joints or brace are the issue. If the whole post moves when you push on the gate, the post is the problem, and no amount of work on the gate will fix it.
Check the post at ground level with a screwdriver. Sound timber resists the tip; rotten timber lets it sink in easily. Look at the brace too. On a ledged and braced gate, the brace must run upwards from the bottom rail on the hinge side to the top rail on the latch side. Fitted the other way, it does nothing to stop sagging.
| Symptom | Likely cause | Typical fix |
|---|---|---|
| Hinges move when gate is lifted | Loose or stripped screws | Longer screws or coach bolts into sound timber |
| Frame flexes out of square | Loose joints or poor brace | Square up, re-glue or pin joints, refit brace |
| Whole post moves | Rotten or leaning post | Replace post, £180–£350 per post |
| Gate drops over months | Hinges too light | Heavier hinges, longer straps |
| Bottom scrapes after rain | Timber swelling | Plane bottom edge, treat end grain |
Fixing loose hinges and joints
Where screws have stripped, simply tightening them will not hold for long. Better options are moving the hinge slightly so screws bite into fresh timber, using longer screws, or switching to coach bolts that pass right through the gate frame. On heavier gates, longer strap hinges spread the load further along the rails and resist sagging much better than short hinges.
To square a frame, prop the latch end up with wedges until the gate is square, then fix the joints in that position. Loose joints can be re-glued with exterior adhesive, pinned or reinforced with galvanised corner brackets on the inside face. Once the frame is square and tight, the brace can be refitted to lock it in place.
Fitting a diagonal brace
If the gate has no brace, or the brace is fitted the wrong way, fitting one correctly is the single most effective anti-sag repair. With the gate propped square, cut a length of treated timber to run from the bottom rail at the hinge side to the top rail at the latch side. The ends should be cut to sit tightly against the rails so the brace is in compression, then screwed through the boards from the front.
On gates where a timber brace would spoil the look, a steel anti-sag kit with a cable and turnbuckle can do the same job running the opposite diagonal, in tension. These kits let you adjust the gate over time but are more visible and suit utility gates better than show gates.
When the post is the problem
A leaning or rotten hinge post is the most common reason a repair does not last. Timber posts set straight into concrete often rot just at ground level, where water collects between the wood and the concrete. Once that happens the post rocks and the gate drops with it.
Replacing a post means digging out the old post and concrete, setting a new treated softwood, hardwood or steel-reinforced post plumb, and letting the concrete cure before the gate is rehung. In the UK this typically costs £180–£350 per post. Setting the new post with the concrete shaped to shed water away from the timber helps it last much longer.
DIY or call a professional
Tightening hinges, fitting longer screws and adding a brace to a small garden gate are reasonable DIY jobs if you have basic tools and someone to help hold the gate. Replacing a post, rehanging heavy double driveway gates or rebuilding a gate frame is harder. It needs digging out old concrete, getting the new post perfectly plumb and handling heavy timber safely.
A professional repairer typically rehangs and braces a sagging side gate for £90–£180, which is often worth it for the time saved and a result that stays square. Through us, you can request quotes from vetted, insured local specialists who handle everything from a quick rehang to a full post replacement.
Questions people also ask
Which way should the brace go on a wooden gate?
The brace should run from the bottom of the gate on the hinge side up to the top on the latch side. In that direction it is in compression and pushes the latch end up, stopping sagging. If it runs from the top hinge corner down to the bottom latch corner, it offers little resistance and the gate will keep dropping.
Can I fix a sagging gate without taking it off?
Often, yes. Tightening hinges, adding longer screws and fitting a brace can be done with the gate in place if you prop the latch end square with wedges first. Replacing a post or rebuilding joints usually means taking the gate off, which is easier with two people.
Do anti-sag kits work on wooden gates?
Anti-sag kits use a steel cable and turnbuckle running diagonally from the top hinge corner to the bottom latch corner. Tightening the turnbuckle pulls the latch end up. They work well on utility and lighter gates and allow adjustment later, but a properly fitted timber brace is neater and does not need tightening.
Written and checked by the Wooden Gate Repair team. Read our editorial policy.
More guides
Wooden Gate Repair Cost UK: 2026 Prices for Common Jobs
In the UK in 2026, rehanging and bracing a sagging side gate typically costs £90–£180. Replacing a timber gate post costs £180–£350 per post, new…
Replacing a Rotten Gate Post: Methods, Materials and Costs
A rotten gate post is replaced by removing the gate, digging out the old post and its concrete, setting a new treated softwood, hardwood or…
How to Treat and Refinish a Wooden Gate: Oil, Stain or Paint?
Choose oil for hardwood gates you want to keep looking natural, stain or a coloured preservative for softwood gates, and exterior paint for a solid…
Repair or Replace a Wooden Gate? How to Decide
Repair a wooden gate if the frame is mostly sound and the problem is sagging, loose fittings, a few rotten boards or a rotten post. Replace it if rot…
Get a free wooden gate repair quote
Tell us what you need and we'll come back with a clear price.
Request a quote